ALIŞVERİŞ SEPETİNİZ (BOŞ) HESAP YÖNETİMİ
Merhaba, üye girişi yapmak için tıklayın.
ATV12H018M2X-HIZ KONTROL CİHAZI ATV12 - 0,18KW - 0,25HP - 200..
246 0.0
0.00 https://www.endustriyelticaret.com Stoklarda! Hemen Sipariş Ver!

ATV12H018M2X-HIZ KONTROL CİHAZI ATV12 - 0,18KW - 0,25HP - 200..

Stok KoduATV12H018M2X
Yeni
Ürün
Kdv Hariç 0,00  + KDV
Kdv Dahil 0,00 
Stokta var
Bu üründen Adet
Ürün Açıklaması
Ana
Ürün serisi Altivar 12
Ürün ya da bileşen tipi Değişken hızlı sürücü
Ürün varış yeri Asenkron motorlar
Ürüne özel uygulama Basit makine
Montaj stili Soğutma bloklu
Bileşen adı ATV12
Set başına miktar 1'li set
EMC filtresi Entegre
Dahili fan Olmadan
Fazların ağ sayısı 1 faz
[Us] nominal besleme gerilimi 200...240 V - 15...10 %
Motor gücü kW 0,18 kW
Motor gücü hp 0,25 hp
Haberleşme port protokolü Modbus
Hat akımı 3,4 A -de 200 V
2,8 A -de 240 V
Hız aralığı 1…20
Geçici aşırı moment 150…170 % of nominal motor torque depending on drive rating and type of motor
Asenkron motor kontrol profili Sensörsüz akı vektör kontrolü
Gerilim/frekans oranı (V/f)
Karesel gerilim/frekans oranı
IP koruma derecesi IP20 without blanking plate on upper part
Gürültü seviyesi 0 dB
 
Tamamlayıcı
Besleme frekansı 50/60 Hz +/- 5 %
Konnektörün tipi 1 RJ45 (on front face) for Modbus
Fiziksel arayüz 2 telli RS 485 için Modbus
Iletim çerçevesi RTU için Modbus
Iletim hızı 4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
Adreslerin sayısı 1…247 için Modbus
Haberleşme hizmeti Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
Muhtemel hat Isc 1 kA
Sürekli çıkış akımı 1.4 A at 4 kHz
Maksimum geçici akım 2.1 A for 60 s
Hız kontrol cihazı çıkış frekansı 0,5…400 Hz
Nominal anahtarlama frekansı 4 kHz
Anahtarlama frekansı 2...16 kHz ayarlanabilir
4...16 kHz değer kaybı faktörü ile
Frenleme torku Up to 70 % of nominal motor torque without braking resistor
Motor kayma kompanzasyonu Ayarlanabilir
Fabrikada mevcut
Çıkış gerilimi 200...240 V 3 phases
Elektrikli bağlantı Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC)
Sıkma torku 0,8 N.m
Yalıtım Güç ve kontrol arasındaki elektrik
Besleme Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection
Analog giriş sayısı 1
Analog giriş tipi Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm
Dijital giriş sayısı 4
Dijital giriş tipi Programmable LI1...LI4 24 V 18...30 V
Dijital giriş lojiği Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
Örnekleme süresi 20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input
Doğrusallık hatası +/- 0.3 % of maximum value for analogue input
Analog çıkış sayısı 1
Analog çıkış tipi AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
Dijital çıkış sayısı 2
Dijital çıkış tipi Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
Minimum anahtarlama akımı 5 mA at 24 V DC for logic relay
Maksimum anahtarlama akımı 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Hızlanma ve yavaşlama rampaları 0 - 999,9 sn arası doğrusal
S
U
Durana kadar frenleme By DC injection, <30 s
Koruma tipi Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
Frekans çözünürlüğü Analog input: converter A/D, 10 bits
Ekran birimi: 0,1 Hz
Zaman sabiti 20 ms +/- 1 ms for reference change
İşaretleme CE
Çalışma konumu Dikey +/- 10 derece
Yükseklik 143 mm
Genişlik 72 mm
Derinlik 102,2 mm
Ürün ağırlığı 0,7 kg
 
Ortam
Elektromanyetik uyumluluk Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
Surge immunity test level 3 conforming to EN/IEC 61000-4-5
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
Elektromanyetik emisyon Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable
Conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2...12 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable <10 m
Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m
Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Ürün sertifikaları C-Tick
UL
GOST
NOM
CSA
Titreşim direnci 1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6
Darbe dayanımı 15 gn conforming to EN/IEC 60068-2-27 for 11 ms
Bağıl nem 5…95 % yoğuşmasız 'e uygunIEC 60068-2-3
5…95 % damlayan su olmadan 'e uygunIEC 60068-2-3
Depolama ortam koşulları -25…70 °C
Çalışma için ortam hava sıcaklığı -10…40 °C protective cover from the top of the drive removed
40…60 °C with current derating 2.2 % per °C
Çalışma yüksekliği > 1000...2000 m with current derating 1 % per 100 m
Whatsapp Whatsapp
Sizlere en iyi alışveriş deneyimini sunabilmek adına sitemizde çerezler(cookies) kullanmaktayız. Detaylı bilgi için lütfen tıklayınız.
×